Procom PCSD25RT Betriebsanleitung

   ITEM#0293809BLOWER ACCESSORYQuestions, problems, missing parts?Beforereturningtoyourretailer,callourcustomerservicedepartmen

10Fig.1313.Unscrewthecontrolpanel(twoscrews).Pullthecontrolpaneloutwithoutdisconnectingtheignitorwire.SeeFig.13.Fig.1414.Feedth

11Fig.1616.Pushtherockerswitch(E)intothecontrolpanel.SeeFig.16.Fig.1717.Re-attachthecontrolpanelwiththetwoscrewstakenoffins

12Fig.1919.Re-attachthegrillwiththetwoscrewstakenoffinstep12.SeeFig.19.Fig.2020.Re-attachthetoppanelwiththescrewstakenoffin

13Installation blower assembly positionInstallwireandgroundingInstalltemperaturesensorInstallrockerswitchInstallblower

14Fig.11.Unscrewandremovethebloweraccesspanel.SeeFig.1.Beforeinstallingtheblower,becertaintoturnofftheunit,andallowtimeforun

15Hardware UsedM4.2X8screwx3AAFig.3Fig.43.Attachthepowercord(A)tothebloweraccesspanelwithM4.2X8screws(AA).SeeFig.3.4.Attachthe

16Fig.5a5.InsertthewiresmarkedwithAUTO,OFFandMANintowireslotontherightcorner.Feedthemasclosetothebottomaspossible.SeeFig.

17Fig.66.Connecttwoblackandyellowwires(femaleports)markedT1andT2withthetwomaleportsonthetemperaturesensor(C).SeeFig6.Fig.77

18Fig.1010.AttachthegroundingporttothetabontherightsideofthebloweraccessholewithM4.2X8screws(AA).SeeFig.10.Fig.1111.Pushthe

19Fig.12Hardware Used12.Bundlethewiringwiththecabletie(BB).SeeFig.12.ForModel#CRHQD250T(Item#0293811),andQstoveonly.CableTiex

2PART DESCRIPTION QuantityA PowerCord 1B Blower 1C TemperatureSensor 1D ConnectorWires 1E RockerSwitch 1PACKAGE CONTENTSACBDE

2016.Unscrewtwoscrewsonthegrill.Removethegrillandlogs.SeeFig.16.ForModel#CRHQD250T(Item#0293811),Qstove,andBD32seriesonly

2118.Rotatinghandle,openthedoor,removethelogs.SeeFig.18.ForModel#PCSD25RTonly.Fig.18Fig.1919.Unscrewscrewsforxingfrontlogbra

2221.Unscrewscrewsforxingcontrolpanel.SeeFig.21.ForModel#CRHFD400RT-M-M(Item#0328248),andFBD400seriesonly.22.Unscrewscrewsfor

23Fig.2525.ConnecttheAUTO,OFF,MANwirestothethreeecorrespondingmaletabsontherockerswitch(E).SeeFig.25.EAUTOOFFMANFig.2424.Feedt

24Fig.2727.Pushtherockerswitch(E)intothecontrolpanel.SeeFig.27.ForModel#CRHSD25RT(Item#0328253),CRHFD400RT-M-M(Item#0328248),

25Fig.3030.Re-xControlPanel.SeeFig.30.ForModel#CRHFD400RT-M-M(Item#0328248),andFBD400seriesonly.Fig.3131.Laythelogsaccording

26Fig.33Fig.3433.Laybackthelogsaccordingtotheoriginallayout,andshutthedoor.SeeFig.33.ForModel#CRHSD25RT(Item#0328253)only.34

27Installation blower assembly position For Model # CRHQD250T (Item # 0293811), and Q stove.InstallrockerswitchInstallblowerInstalltemperaturesen

28Installation blower assembly position For Model BD23 series InstalltemperaturesensorInstallwireandgroundingInstallblowerInstallrockerswi

29Installation blower assembly position For Model # CRHSD25RT (Item # 0328253), and PCSD25RT.Installation blower assembly position For Model # CRHFD40

3HARDWARE CONTENTSAA210CableTieM4.2X8ScrewWARNINGS AND CAUTIONSWARNING• Readallinstructionsandwarningscarefullybeforestartinginstallation.

30ELECTRICAL CONNECTIONA15amp,120Volt,60Hzcircuitwithaproperlygroundedoutletisrequired.Preferably,thereplacewillbeonadedicated

31CARE AND MAINTENANCEAlways disconnect the appliance from the main power supply and allow it to cool before any servicing operation.Themotorsusedo

32REPLACEMENT PARTSNOTE:Useonlyoriginalreplacementparts.Thiswillprotectyourwarrantycoverageforpartsreplacedunderwarranty.PARTS UNDER W

33REPLACEMENT PARTS LISTForreplacementparts,callourcustomerservicedepartmentat1-877-886-5989,8:00a.m-4:30p.m.,EST,Monday-Fridayore

34WARRANTYINFORMATIONKeepThisWarrantyIMPORTANT:WeurgeyoutollyourwarrantyregistrationcardwithinTEN(10)daysofdateofinstallation,com

4Fig.1ASSEMBLY INSTRUCTIONSPREPARATIONBeforebeginningassemblyofproduct,makesureallpartsarepresent.Comparepartswithpackagecontentslist

5Hardware UsedM4.2X8screwx3AAFig.2Fig.32.Attachthepowercord(A)tothereplacewithM4.2X8screws(AA)onthetopcover.SeeFig.2.3.Attach

6Fig.44.AttachthegroundingporttoshellboardwithM4.2X8screw(AA);refertogroundinglabel.Besuretoinsertthegasketbetweentheshellbo

7Fig.66.Insertthemaleport,whichisontheblackpowersupplywire(markedP2),intothecorrespondingfemaleport(markedP2).SeeFig.6.Fig.7

8Fig.88.IMPORTANT:Bundlethewiringtothetopboardwiththecabletie(BB).Thisistoavoidanyheatdamagetotheinsulationboard.SeeFig.

9Fig.1010.InsertthewiresmarkedwithAUTO,OFFandMANintowireslotontherightcorner.Feedthemasclosetothebottomaspossible.SeeFig.