Procom MN060HBA Bedienungsanleitung PDF herunterladen (Seite 12)

OPERATING YOUR HEATER

FOR YOUR SAFETY

READ BEFORE LIGHTING

A. When lighting the pilot, follow

these instructions exactly.

B. BEFORE LIGHTING smell all

around the appliance area for gas.

Be sure to smell next to the floor

because some gas is heavier than

air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

 Do not try to light any appliance.

 Do not touch any electric

switch, do not use any phone

in your building.

 Immediately call your gas

supplier from a neighbor’s

phone. Follow the gas

supplier’s instructions.

 If you cannot reach your gas

supplier, call the fire department.

C. Use only your hand to push

in or turn the gas control knob.

Never use tools. If the knob will

not push in or turn by hand, don’t

try to repair it , call a qualified

service technician or gas supplier.

Force or attempted repair may

result in a fire or explosion.

D. Do not use this appliance if

any part has been under water.

Immediately call a qualified service

technician to inspect the appliance

and to replace any part of the control

system and any gas control which

has been under water.

LIGHTING

INSTRUCTIONS

WARNING: If you do not follow

these instructions exactly, a fire or

explosion may result causing

property damage, personal injury

or loss of life.

1. STOP! Read the safety

information on the side of heater.

2. Make sure equipment shutoff

valve is fully open.

3. Turn control knob clockwise

to the OFF position.

4. Wait five(5) minutes to clear

out any gas. Then smell for gas,

including near the floor. If you

smell gas, STOP! Follow

“B” in the

safety information on the side of

heater. If you don’t smell

gas, go to the next step.

5. Turn control knob counterclock-

wise

to the PILOT position.

Press in control knob for five(5)

seconds. (see Figure18).

Note: You may be running

this heater for the first time

after hooking up to gas supply.

If so, the control knob may

need to be pressed in for 30

seconds. This will allow air to

bleed from the gas system.

 If control knob does not pop

up when released, contact a

qualified service person or

gas supplier for repairs.

6. With control knob pressed in,

push down and release ignitor

button. This will light pilot. The

pilot is attached to the front of

burner. The pilot can be seen

through the glass panel. If

needed, keep pressing ignitor

button until pilot lights.

Note: If pilot does not stay lit, refer

to Troubleshooting, pages 14 through

16. Also contact a qualified service

person or gas supplier for repairs.

Until repairs are made, light pilot with

match.To light pilot with match, see

Manual Lighting Procedure.

7. Keep control knob pressed

in for 30 seconds after lighting

pilot. After 30 seconds, release

control knob.

 If control knob does not pop

up when released, contact a quali-

fied service person or gas

supplier for repairs.

Note: If pilot goes out,repeat steps 3

through 7.This heater has a safety

interlock system. Wait one(1)

minute before lighting pilot again.

8. Turn control knob counter-

clockwise

to desired heating

level. The main burner should

light. Set control knob to any

heat level between HI and LO.

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

1. Turn control knob clockwise

to the OFF position.

2. Turn off all electric power to the

appliance if service is to

be performed.

Shutting Off Burner Only (pilot

stays lit )

Turn control knob clockwise

the PILOT position.

Figure 18 - Control Knob in The

OFF Position

Figure 19 - Pilot

CAUTION: Do not try to ad-

just heating levels by using the

equipment shutoff valve.

THERMOSTAT CONTROL OPERATION

The thermostatic control used on this

model differs from standard

thermostats.Standard thermostats

simply turn on and off the burner. The

thermostat used on this heater senses

the room temperature. At times the

room may exceed the set temperature.

If so,the burner will shut off. The burner

will cycle back on when room tempera-

ture drops below the set temperature.

The control knob can be set to any com-

fort level between HI and LO.

Note: The thermostat sensing bulb mea-

sures the temperature of air near the

heater cabinet.This may not always agree

with room temperature(depending on

housing construction, installation location,

room size, open air temperatures,etc.)

Frequent use of your heater will let you

determine your own comfort levels.

THERMOSTAT MODEL

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 22 23

Kommentare zu diesen Handbüchern

Keine Kommentare

Procom MN060HBA Bedienungsanleitung Seite 12

Kommentare zu diesen Handbüchern