ITEM #0309526 VENT FREE GAS FIREPLACE SYSTEM MODEL #SSFBD23T-5-HM WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWEDEXACTLY, A FIRE
10 WARNING: If the area in which the heater may be operated is smaller than that dened as an unconned space or if the building is of unusually
11Fig. 4 - Minimum Clearance to Wall and CeilingINSTALLATION NOTICE: This heater is intended for use as supplemental heat. Use this heater
12CONNECTING TO GAS SUPPLY WARNING: A qualied technician must connect heater to gas supply. Follow all local codes. WARNING: This appliance requ
13 CAUTION: Use only new black iron or steel pipe. Internally tinned copper tubingmay be used in certain areas. Check your local codes. Use pipe of ½
14CAUTION: Two gas line installation at the same time is forbidden. Do not open the cover while the heater is running. Heater is pre-set at factory fo
15Fig. 10Fig. 9Fig. 8NATURAL GASPROPANE GASPLUGNATURAL GASPROPANE GASPLUG
16CHECKING GAS CONNECTIONS WARNING: Test all gas piping and connections for leaks after installing or servicing. Correct all leaks immediately
17INSTALLING LOGSFig. 13 - Installing Log SetIMPORTANT: Make sure log does not cover any burner ports (see Fig. 13). It is very important to install t
18OPERATIONFOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a re or explosion may result causing pro
19LIGHTING INSTRUCTIONSUnscrew ignitor cap and install a AAA battery with the + pointing out. Replace cap.1. STOP! Read the safety information on page
2 TABLE OF CONTENTSITEM #0309526 VENT FREE GAS FIREPLACE SYSTEMInput Rating 23,000 BTU/Hr 23,000 BTU/HrGas Type Natural LP/PropaneIgnition Piezo/Aut
20TO TURN OFF GAS TO APPLIANCE Shut off heater.Turn Control Knob clockwise to the OFF position. Do not force. MANUAL LIGHTING PROCEDURE (Mat
21INSPECTING BURNERSCheck pilot ame pattern and burner ame patterns often. PILOT FLAME PATTERN 1. Turn control knob to pilot position2. Inspect pilo
22CARE AND MAINTENANCECLEANING BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLEWe recommend that you clean the unit every three months or after 2500 ho
23CLEANING ODS/PILOTUse a vacuum cleaner, pressurized air, or a small, soft bristled brush to clean.A yellow tip on the pilot ame indicates dust and
24TROUBLESHOOTING WARNING: If you smell gas: • Shut off gas supply. • Do not try to light any appliance. • Do not touch any electrical switch; do n
25Problem Possible Cause Corrective ActionODS/pilot lights but ame goes out when control knob is released.1. Control knob is not fully pressed in
26Problem Possible Cause Corrective ActionSlight smoke or odor during initial operation.1. Residues from manufacturing process.1. Problem will sto
27REPLACEMENT PARTSNOTE: Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty.PARTS UNDER W
28REPLACEMENT PARTS LISTPart. Description Part # QTY1 Burner Assembly FBB28D01-B 12 DF ODS NDD0308 13 T-Stat Valve SIT545-200 14 Piezo Ignitor AL092-
29REPLACEMENT PARTS LISTFor replacement parts, call our customer service department at 1-866-573-0674, 8:00 a.m - 4:30 p.m., EST, Monday - Friday or e
3IMPORTANT SAFETY INFORMATIONIMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this heater.
30
31BASE AND SAFETY MOUNTING BRACKETSHARDWARE CONTENTS PicturePart Description Quantity (Shown to size)AAST4.8 Screw - 2 3/8
32ASSEMBLY INSTRUCTIONS1. Push base into bottom of mantel. Adjust the base so that both the left and right side of the base are ush with the mantel.
33in.in.DDFig. 3Hardware UsedWall Anchorsx 63. Position the safety mounting brackets (DD) according to Fig. 3. Use a pencil to mark the center of the
34Fig. 66. Position the replace to desired position. Lift the entire mantel up and slip the right angle hooks over the safety mounting brackets (DD)
352-YEAR LIMITED WARRANTYThe manufacturer warrants this product to be free from defects in workmanship and material present at time of shipment from t
41. Do not place Propane/LP supply tank(s) inside any structure. Propane/LP supply tank(s) must be placed outdoors.2. This heater needs fresh ai
515. Do not add extra logs or ornaments such as pine cones, vermiculite, or rock wool. Using these added items can cause sooting. Do n
6SAFETY PILOTThis heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS/pilot shuts off the heater if there is not
7UNPACKING 1. Remove top inner pack.2. Tilt carton so that heater is upright. 3. Remove protective side packaging.4. Slide heater out of carto
8AIR FOR COMBUSTION AND VENTILATION WARNING: This heater should not be installed in a conned space or unusually tightconstruction unless provisions a
9DETERMINING FRESH-AIR FLOW FOR HEATER LOCATIONDetermining if You Have a Conned or Unconned SpaceUse this worksheet to determine if you have a conn
Kommentare zu diesen Handbüchern